Visit My Web Page

 

 

Are you currently hunting for facts about Tools You Need to Install a New Bathtub ?

Mounting a tub isn't precisely rocket science, but it does need solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard task. If the old tub is conveniently easily accessible, the job can move easily; if you have to open a wall surface to get rid of the old tub and place the brand-new tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. See to it you have actually qualified yourself for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to take into consideration employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your restroom if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also material checklist need to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Preparing for the Installation

To start with, the supporting frame provided with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.

 

 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.

 

 

Setting up the Tub

Utilizing the two wooden boards under its feet, place the bathtub in the required setting. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and also check the overflow outlet and also the normal outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has been used at the very least when as this will settle it into its last placement.

 

 

Fitting New Taps

If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type must be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing difficulties with dampness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to sealing, to permit the movement experienced when the tub remains in use. The sealant can split fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed reading our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for spending some time to read through our article post. Are you aware of somebody else who is interested in Tools You Need to Install a New Bathtub ? Why not share it. Thanks for going through it.

Website